We often treat the words “safe” and “airworthy” as if they were synonyms. They’re not.
On the landing roll, something didn’t feel right. The Cessna pulled strongly to the left. The pilot had to apply full right pedal and some right brake to keep it on the runway. As the pilot struggled to make the turnoff, it became clear what was wrong: The left main landing gear tire was flat.
Naturally, this happened away from home base while the pilot was stopping for fuel and lunch in the middle of an important trip. (Doesn’t it always?) The pilot needed to get his airplane fixed and back in the air as quickly as possible. He contacted the local shop on the field—one he wasn’t familiar with—and asked them to recover his aircraft and fix the flat tire.
The mechanic said that he had a new tire in stock for $200 and a tube for $50. Labor was estimated at two hours at a shop rate of $85/hour. It looked like this $100 hamburger would turn into a $500 hamburger. Having few options, the aircraft owner approved the work and asked the mechanic to use his best efforts to complete it quickly so he could get on his way. He then headed for the airport restaurant.
![](https://www.savvyaviation.com/wp-content/uploads/2023/11/Fig1_flattire-842x1024.jpg)
We’ve Got a Problem
When the owner returned to the shop two hours later, he found that his airplane was on jacks with the left main wheel off. He was not a happy camper, and sought out the mechanic to find out what was holding things up.
“We’ve got a problem,” the mechanic told the owner. “Your brake disc is below minimum thickness. If I order one now, I can have it here tomorrow.”
The owner explained to the mechanic that he didn’t have time for that, and directed him to finish installing the tire and tube so the owner could be on his way.
“The Cleveland Wheel & Brake service manual states that the minimum thickness for your brake disc is 0.327 inches, and yours measures 0.324 inches,” replied the mechanic, applying a digital micrometer to the disc and demonstrating to the owner that his measurement was indeed correct. He then showed the owner the table of limits in the service manual that specified 0.327 inches as the minimum thickness for the disc. “I’m not going to be able to sign off the work with the disc worn below limits.”
The owner was understandably upset. He’d hired the mechanic to change his flat tire, not to inspect his brakes. He couldn’t believe that this @#$%! mechanic was going to try to hold his airplane hostage over a .003” discrepancy on the brake disc. Surely this could wait until he got home from his trip, couldn’t it?
That’s when the owner called me.
Catch 22
After listening to the owner’s blow-by-blow description of what happened, I knew immediately that he wasn’t going to like my answer.
I told the owner I agreed that it would almost certainly be safe to defer replacing the brake disc until the owner got home from his trip. But I also agreed with the mechanic that he could not properly approve the aircraft for return to service without replacing the disc, because the disc was clearly unairworthy. Both the owner and the mechanic were right.
FAR §43.9—which sets forth the requirements for maintenance record entries—says that the mechanic’s signature “constitutes the approval for return to service only for the work performed,” and that it denotes that the work “has been performed satisfactorily.” In plain English, this means that the mechanic’s signature does not signify that the aircraft is airworthy, only that the work performed is airworthy.
For example, if the mechanic who was hired to change the flat tire happened to notice that the airplane’s rudder was damaged, that would not prevent him from signing off the tire change. So long as the mechanic did not perform work on the rudder, the fact that the rudder was damaged would have no bearing on the mechanic’s sign-off of the tire change. A conscientious mechanic would point out the rudder damage to the owner, and might even say, “I wouldn’t fly the airplane in that condition if I were you,” but he could not reasonably withhold his signature on the logbook entry, since the rudder damage is completely unrelated to the work he performed.
But in this case, the owner hired the mechanic to fix the flat tire. Changing the tire and tube removing the wheel from the aircraft and disassembling it, and that required the brake disc to be removed and reinstalled. Unlike the rudder, the brake disc unavoidably became part of the work performed by the mechanic. I told the owner that in my opinion the mechanic could not reasonably be expected to sign off the work once he knew that the brake disc was unairworthy. Catch 22.
I also told the owner that, legalities aside, it really made sense for him to have the mechanic replace the brake disc and brake linings now. After all, the airplane was on jacks, the wheel was off and split, and changing the disc now would involve no additional labor. Doing it later would require repeating all that work a second time, including demounting and remounting the new tire and tube. It just didn’t make sense to defer this work.
In the end, the owner reluctantly accepted my advice, approved the new disc and linings, and checked into a local hotel. The next day he was on his way, a bit poorer and a bit wiser about the difference between “safe” and “airworthy.”
Safe vs. Airworthy
We often treat the words “safe” and “airworthy” as if they were synonyms. They’re not. For an aircraft, engine, propeller, appliance or part to be “airworthy” it must meet both of the following criteria:
- It must comply with its original or properly altered type design.
- It must be in condition for safe operation.
Thus, an airworthy component is safe by definition, but a safe component is not necessarily airworthy. The brake disc was almost certainly in adequate condition to complete the trip safely, but it definitely did not comply with its type design because it was .003” below the minimum thickness (service limit) prescribed by the manufacturer.
Note that the two components of airworthiness are quite different. One is objective, the other subjective. Whether a component complies with its type design is normally a clear-cut issue: Either it meets specs or it doesn’t. If the brake disc measures 0.327” or more, then it’s airworthy; if it measures 0.326” or less, then it’s unairworthy. On the other hand, whether a component is in condition for safe operation is subjective: It’s someone’s opinion. Two mechanics might inspect a damaged rudder, and one might feel that the damage is minor and the rudder in condition for safe operation, while the other might disagree.
Legal to fly?
In a situation like this, how can we know whether or not we’re legal to fly? There are two relevant regulations. The first is FAR §91.7:
§ 91.7 Civil aircraft airworthiness.
(a) No person may operate a civil aircraft unless it is in an airworthy condition.
(b) The pilot in command of a civil aircraft is responsible for determining whether that aircraft is in condition for safe flight. …
This is a subtly worded regulation. Paragraph (a) says that we can’t fly an aircraft unless it is in an airworthy condition, but it does not explain how pilots are supposed to know whether or not the aircraft they are about to fly is airworthy. As pilots, are we responsible for determining the airworthiness of the aircraft? Are Cessna pilots expected to micrometer the brake discs before each flight? The regulation doesn’t say, but it doesn’t seem like a reasonable expectation. I think the FAA expects aircraft owners to hire mechanics to make these airworthiness determinations—at least once a year—and then abide by those determinations.
Paragraph (b) states that the PIC is responsible for determining whether the aircraft is in condition for safe flight. It doesn’t say that the PIC is required to determine if it’s airworthy, only whether it’s safe to fly. What this suggests is that the PIC is expected to make a subjective determination about safe condition before he flies the aircraft, but is expected to rely on mechanics to make the objective determination about conformance to type design. In short, I don’t think the FAA expects a pilot to use a micrometer, but it does expect a mechanic to do exactly that.
[NOTE: Experimental aircraft have no type design, so we can’t properly use the world “airworthy” in connection with such an aircraft. All we can say about an experimental is that it “is in condition for safe operation.” That’s why experimentals don’t have an “annual inspection” each year, they have a “condition inspection.”]
The second relevant regulation is FAR §91.407:
§ 91.407 Operation after maintenance…
(a) No person may operate any aircraft that has undergone maintenance … unless—
(1) It has been approved for return to service by a person authorized under §43.7 of this chapter; and
(2) The maintenance record entry required by §43.9 or §43.11, as applicable, of this chapter has been made.
An aircraft is grounded by the very act of committing maintenance upon it. It s ungrounded thereafter only by a maintenance record entry signed by an authorized person (usually an A&P mechanic or a certified Repair Station).
A Thought Experiment
This Cessna owner wasn’t exactly the hands-on wrench-swinging type, but let’s imagine that he was. For purposes of this thought experiment, imagine further that the owner decided that he absolutely positively had to continue his trip without delay, and simply could not remain overnight waiting for the new brake disc to arrive. Perhaps our imaginary owner could have said something like this to the mechanic:
“Mr. A&P, I fully appreciate your reluctance to sign off this tire change with a brake disc that you have determined to be unairworthy. If I were in your position, I’d probably do exactly the same thing. I would never try to pressure you into signing off a logbook entry if you were not entirely comfortable doing so.
“However, I simply cannot delay my departure until tomorrow when the new disc would arrive. Therefore, here’s what I propose: A tire change is classified in FAR Part 43 Appendix A(c) as ‘preventive maintenance’ and is a task that I am therefore permitted to perform and sign off myself without A&P supervision.
“Therefore, I would like to perform the tire change myself—with your guidance and assistance (since I’ve never changed a tire before), not to mention your tools—and sign it off myself as owner-performed preventive maintenance. The tire-change procedure in the maintenance manual does not require me to measure the brake disc, so I won’t. I will pay you for your time and for the parts, but I will not ask you to sign off the work or hold you responsible for its airworthiness. Your invoice will show that you sold me the tire and tube and that I installed it myself. Is that acceptable to you?”
If the mechanic was in a generous mood, perhaps he might agree to this. If the shop was an FAA-certified Part 145 Repair Station, then most likely he could not agree to it.
You bought a plane to fly it, not stress over maintenance.
At Savvy Aviation, we believe you shouldn’t have to navigate the complexities of aircraft maintenance alone. And you definitely shouldn’t be surprised when your shop’s invoice arrives.
Savvy Aviation isn’t a maintenance shop – we empower you with the knowledge and expert consultation you need to be in control of your own maintenance events – so your shop takes directives (not gives them). Whatever your maintenance needs, Savvy has a perfect plan for you: